Crane & Hoist Equipment & SystemsCrane & Hoist Parts
and Accessories
Service & RepairsInspection SystemsTrainingOur Manufacturers
Sievert Crane & Hoist > Crane & Hoist Parts & Accessories > Duct-O-Bar Figure 8 (FE) Components  
 

Duct-O-Bar Figure 8 (FE) Components


Click on a Product to view details.

Angle Brackets for Web Mounting

Angle Brackets for Web Mounting

(5)
Brackets are galvanized 12 gage rolled steel channel. Hangers are priced separately, but will be factory installed at no charge when hanger locations are shown on sketch.
Straight Brackets for Top Flange Mounting

Straight Brackets for Top Flange Mounting

(11)
Brackets are galvanized 12 gage rolled steel channel. Hangers are priced separately, but will be factory installed at no charge when hanger locations are shown on sketch.
Straight Brackets w/ Mounting Plate for Web Mounting

Straight Brackets w/ Mounting Plate for Web Mounting

(11)
Brackets are primed 12 gage rolled steel channel with mounting plate and hardware. Hangers are priced separately, but will be factory installed at no charge when hanger locations are shown on sketch.
Z-Brackets for Lateral Mounted Conductors

Z-Brackets for Lateral Mounted Conductors

(5)
Brackets are red primed 10 gage steel. Hangers are priced separately, but will be factory installed at no charge when hanger locations are shown on sketch.
Snap-In Type Hanger Assemblies

Snap-In Type Hanger Assemblies

(5)
These hangers are not recommended for curves, switches or short runs unless separate anchors are used.
Snap-In Type Spring Hanger and Insulator Assemblies for Outdoor, Wet and Dirty Applications

Snap-In Type Spring Hanger and Insulator Assemblies for Outdoor, Wet and Dirty Applications

(3)
Clamp Type Hanger Assemblies for All Conductor Systems

Clamp Type Hanger Assemblies for All Conductor Systems

(3)
Clamp Type Hanger and Insulator Assemblies for Outdoor, Wet and Dirty Applications

Clamp Type Hanger and Insulator Assemblies for Outdoor, Wet and Dirty Applications

(3)
Clamp Type Special Hanger Assemblies

Clamp Type Special Hanger Assemblies

(2)
Snap-In Type Special Hanger Assemblies

Snap-In Type Special Hanger Assemblies

(4)
Mushroom Insulators with Hardware

Mushroom Insulators with Hardware


30% Glass-filled Nylon — 400°F rated. Suitable for chemical or oil-laden atmospheres.
Power Feeds with Insulating Case

Power Feeds with Insulating Case

(4)
End Power Feeds

End Power Feeds

(2)
Expansion Gap Assemblies

Expansion Gap Assemblies

(18)
Each assembly consists of a ten-foot conductor bar, insulating cover, connector pins for one end, guide assembly, two power feeds with a jumper cable and hanger set.
Pickup Guide Assembly

Duct-O-Bar Figure 8 (FE) Special Application Components

(12)
Collector Mounting Post

Collector Mounting Post


Mounting plate is 4" square with 3" hole spacing for C-Series and P-Series Collectors. (Contact factory for special lengths or finishes.)
C-Series Collector Assemblies

C-Series Collector Assemblies

(4)
C-Series Collectors are used on short continuous run systems. They feature steel pivot points for good tracking capability.
P-Series Collector Assemblies-Single Shoe

P-Series Collector Assemblies

(12)
P-Sehes Collectors are used on straight and curved runs and transfers. The pantograph design provides virtually constant spring pressure for the entire stroke range. Lateral Mount Collectors are provided with spring balance. Conductor Bars must be spaced at least 3 inches apart. To order bronze collectors with stainless steel hardware, add "BR" to the catalog number. Call factory for prices.
Additional Components

Duct-O-Bar Figure 8 (FE) Additional Components

(7)
Conductor Bar Cleaning Accessories

Conductor Bar Cleaning Accessories

(10)
Site created by ThomasNet Web Solutions and powered by Navigator Platform